Search found 11 matches

by gooch
Mon Jul 02, 2018 10:07 pm
Forum: Rimfire Handguns
Topic: The new Ruger Mark IV Target and Hunter
Replies: 13
Views: 5983

Re: The new Ruger Mark IV Target and Hunter

I decided to get the Mark iv Hunter, loved the 6.88 inch fluted barrel. If you have a Field and Stream store nearby ( yes, I know they Played to the anti-gun media and took all ARs out) be aware that they do price matching. I showed an add from Bud's Guns on my phone and saved over $100 off their pr...
by gooch
Sat Apr 07, 2012 10:24 pm
Forum: Rimfire Handguns
Topic: MarkII sight questions
Replies: 9
Views: 2459

sight adjustment

I drifted the rear over, now the windage is dead on. I am putting an orange sticker 4" higher than my target and can get 7 to 8 out of ten hits. I am holding off on taking material off of the front blade for now. I may order an extra blade next time I need a part and experiment. I use whatever ...
by gooch
Tue Apr 03, 2012 9:47 am
Forum: Rimfire Handguns
Topic: MarkII sight questions
Replies: 9
Views: 2459

mark II sights

Thanks for the information guys!
by gooch
Mon Apr 02, 2012 9:24 pm
Forum: Rimfire Handguns
Topic: MarkII sight questions
Replies: 9
Views: 2459

MarkII sight questions

I recently picked up a used Mark II with 4.5" tapered barrel with fixed sights. I love it except for the sights. At 50' from a rest, my point of impact is about 5" left and 3" low of center. My questions are: Can the fixed rear sight be drifted over? Can I raise the point of impact by...
by gooch
Thu Dec 29, 2011 1:44 pm
Forum: Rimfire Handguns
Topic: My Ruger MKII Competition Target Model
Replies: 18
Views: 6469

Beautiful! if it shoots half as good as it looks, you are definately ready for competition.
by gooch
Fri May 06, 2011 3:08 pm
Forum: Technical Forum
Topic: 22/45 bolt problem
Replies: 6
Views: 2039

Right on the money bullseye!
The hammer was not centered.
by gooch
Tue May 03, 2011 9:57 am
Forum: Technical Forum
Topic: 22/45 bolt problem
Replies: 6
Views: 2039

Thanks for the advice.
I will break it down tonight and check for any allignment issues.
by gooch
Mon May 02, 2011 2:23 pm
Forum: Technical Forum
Topic: 22/45 bolt problem
Replies: 6
Views: 2039

22/45 bolt problem

I have recently installed a new hammer bushing and removed the magazine safety and LCI. Functions test and dry firing were good and the trigger pull felt better. I ran into trouble at the range. The first shot of the magazine was fine, then the bolt would not fully close (out of battery) with all 9 ...
by gooch
Tue Apr 26, 2011 2:10 pm
Forum: Rimfire Handguns
Topic: Mark III Bolt Action Roughness
Replies: 15
Views: 4820

Gunshine, I had the same symptoms after installing a new hammer bushing (to get rid of the magazine safety). It turns out that the bushing was not seated all the way pushing the hammer assembly slightly off center causing the binding.
by gooch
Fri Apr 08, 2011 10:54 am
Forum: Technical Forum
Topic: Ruger MKIII firing pin stop
Replies: 15
Views: 5666

MK III firing pin stop

Thank's Bullseye, I'll keep that in mind.
by gooch
Thu Apr 07, 2011 2:01 pm
Forum: Technical Forum
Topic: Ruger MKIII firing pin stop
Replies: 15
Views: 5666

Ruger Firing pin stop

After detail stripping of my MKIII 22/45, i could not re-insert the firing pin stop (roll pin style). I had a shoot the next day so I improvised and cut the shaft from a dremmel accessory. After smoothing out the cut with a file it fit perfectfully and has held up well so far-about 600 rds. My quest...

Go to advanced search