Search found 1574 matches

by ruger22
Mon Jan 18, 2016 9:43 am
Forum: Handgun Forum
Topic: Kimber revolver
Replies: 4
Views: 23654

Re: Kimber revolver

Kimber K6S revolver. I don't see the big deal. All stainless, at least.

http://www.gunsandammo.com/shot-show-20 ... -revolver/

Price given as $899 here:

http://www.gunsholstersandgear.com/2016 ... -revolver/
by ruger22
Sat Jan 16, 2016 3:33 pm
Forum: Handgun Forum
Topic: Kimber revolver
Replies: 4
Views: 23654

Kimber revolver

This one's for real, on Kimber's website. Saw it first on another forum. Will be unveiled at SHOT on 1-18.

So far they just show a six sided cylinder. Hopefully no plastic.

http://www.kimberamerica.com/REeVOLVE
by ruger22
Mon Jan 11, 2016 12:57 pm
Forum: Gun Talk Community Forum
Topic: BAOM?
Replies: 1
Views: 19318

BAOM?

We haven't heard from you since Christmas Eve. I hope you had a nice Christmas.

Just want to let you know we miss your wit and wisdom.... :D
by ruger22
Mon Jan 11, 2016 12:54 pm
Forum: Handgun Forum
Topic: New Ruger .357/.22 revolver
Replies: 5
Views: 17146

Re: New Ruger .357/.22 revolver

Not my find. It was on another forum, and thought a few here would enjoy it. What made it so good is that it doesn't sink in right away. I didn't think realguns did this king of thing, either.
by ruger22
Sat Jan 02, 2016 5:26 pm
Forum: Handgun Forum
Topic: New Ruger .357/.22 revolver
Replies: 5
Views: 17146

Re: New Ruger .357/.22 revolver

The Magdalunium and Osmium Plus should make a really tough gun......They must be why it weighs 17 pounds?
by ruger22
Fri Jan 01, 2016 5:36 pm
Forum: Handgun Forum
Topic: New Ruger .357/.22 revolver
Replies: 5
Views: 17146

New Ruger .357/.22 revolver

I'd bet Bullseye will appreciate the engineering that went into this thing.

http://www.realguns.com/articles/785.htm
by ruger22
Wed Dec 30, 2015 1:35 pm
Forum: Rimfire Rifles
Topic: Simmons .22 Mag 4X32
Replies: 1
Views: 10723

Simmons .22 Mag 4X32

I got a gift card that just covered it, and Simmons has a $30 rebate offer through January 6. Plus, most shooting forum writers seem to think it is the best low cost scope available. Big upgrade from the $15 3-7X20 Tasco I had on my 10/22 DSP. I chose the 4X32 in black matte. Ditched the supplied ti...
by ruger22
Fri Dec 04, 2015 12:14 pm
Forum: Rimfire Handguns
Topic: Ajax polymer ivory grips for Bearcat no work
Replies: 7
Views: 16003

Re: Ajax polymer ivory grips for Bearcat no work

Since I like them so much, I've went a little berserk on the Bearcats ( like some folks are with 1911's?). I've got one or more of every part except the frame, barrel, cylinder, and trigger guard. I've got five different holsters and five different grips for them. It's not like I "needed" any more g...
by ruger22
Wed Dec 02, 2015 1:09 pm
Forum: Rimfire Handguns
Topic: Ajax polymer ivory grips for Bearcat no work
Replies: 7
Views: 16003

Re: Ajax polymer ivory grips for Bearcat no work

These grips were made by the old Ajax company that went under in 2009. The new company has not re-introduced Bearcat grips, so far. They're on their way back to CDNN. Not sure if they'll even fit OM Bearcats; I didn't think there was any difference in grip fit. Ideally, I'd like a nice fitting black...
by ruger22
Sun Nov 29, 2015 3:45 pm
Forum: Rimfire Handguns
Topic: Ajax polymer ivory grips for Bearcat no work
Replies: 7
Views: 16003

Re: Ajax polymer ivory grips for Bearcat no work

Ajax grip matched to factory grip, definite hole mis-match. Fitting one Ajax panel on the gun, it's obvious the screw hole is slightly to the rear and higher than the factory hole. I can cock the hammer, and the strut covers nearly half the Ajax hole. I tried both sets of Ajax on both of my Bearcats...
by ruger22
Sun Nov 29, 2015 2:07 pm
Forum: Rimfire Handguns
Topic: Ajax polymer ivory grips for Bearcat no work
Replies: 7
Views: 16003

Ajax polymer ivory grips for Bearcat no work

http://www.cdnnsports.com/bearcat-ivory-polymer-ajax.html#.VltLbYvlu01 CDNN listed seven sets. I ordered two. Got 'em and placed them on the guns, Good fit, and look good, but the screw is a little too short. Went to local hardware, which actually has a small section of gun screws. It was a 3-48 scr...
by ruger22
Fri Nov 13, 2015 1:26 pm
Forum: Miscellaneous
Topic: Fun gun
Replies: 11
Views: 33315

Re: Fun gun

I like the line,

"If you get it and didn't work for it, someone else worked for it and didn't get it".

Most of the population is now just "Me, me" and doesn't give a rat's rear about others. If people in WW2 were like they are now, we'd have lost in a year.
by ruger22
Sat Nov 07, 2015 1:37 pm
Forum: Miscellaneous
Topic: See All sight?
Replies: 3
Views: 10685

See All sight?

Anybody actually have one or at least used one? Any opinion? https://seeallopensight.com/ Online reviews are mixed, many sound like planted ads. One issue was the short radius, but red dots and reflector sights are short, too. My issues are the huge branding on the side, and the cost seems high for ...
by ruger22
Sat Nov 07, 2015 1:32 pm
Forum: The Workshop
Topic: To Be a Texas Gunsmith...
Replies: 7
Views: 13314

Re: To Be a Texas Gunsmith...

Let's not forget Super Glue for loose stuff, WD40 for lubing, and and a pint of black Rustoleum for quick reblues.
by ruger22
Fri Oct 02, 2015 3:36 pm
Forum: Miscellaneous
Topic: Old style Bianchi Ranger holsters
Replies: 1
Views: 8263

Old style Bianchi Ranger holsters

Best as I've figured out, they were made in the later Eighties. Anybody have one? I've picked up a few on eBay. Really liked them for Sentinel revolvers I had, and now for my .22 SP101. The strap adjusts with velcro under the belt loop. Mine for a 4 inch barrel are a size four, six inch barrel would...