Drilling & tapping

The place to discuss firearms related modifications or home made shooting equipment.

Moderators: Bullseye, Moderators

Post Reply
stork
Advanced contributor
Advanced contributor
Posts: 333
Joined: Tue Aug 16, 2005 10:12 am
Location: North Dakota

Drilling & tapping

Post by stork » Thu May 07, 2015 5:28 pm

Well, I picked up 2 older MKII's. A 5 1/2" blue and a Stainless 5 1/2" 22/45. As they were older ones neither came drilled & tapped. so I ordered a couple Weigand bases and went to work.

thanks for the drilling template Bullseye.

I've done a few blued ones over the years, so no issues there. Just be careful, measure twice-drill once-measure twice-drill a few thousandths more, etc.

The stainless was a lot tougher steel. Now I had only used that tap for the 3 other holes in the blued one, so it's still in very good shape. Starter tap for the rear, but the two blind holes in front were very hard to keep in line as I'm using a finishing tap. Never broke the tap (haven't done that for a very long time, not fun), but I swore it was about 5 inch pounds from snapping more than once. Lots of Do Drill and cleaning out the hole & tap about every half turn.

Finally did finish about 2 am, put on Ultra Dots and benched them. Mama was gone so I was free to shoot in the middle of the night without disturbing anyone.

It was a very good day!

Al
"A free people ought not only to be armed and disciplined, but they should have sufficient arms and ammunition to maintain a status of independence from any who might attempt to abuse them, which would include their own government.” – George Washington

User avatar
bgreenea3
Master contributor
Master contributor
Posts: 1587
Joined: Sun Sep 06, 2009 9:35 pm
Location: SW Michigan

Post by bgreenea3 » Thu May 07, 2015 7:25 pm

:thumbs up:
"Courage is being scared to death... and saddling up anyway."

-John Wayne

User avatar
Bullseye
Site Admin/Host
Site Admin/Host
Posts: 6382
Joined: Sun Aug 14, 2005 12:23 pm
Location: USA

Post by Bullseye » Fri May 08, 2015 6:15 am

Glad you accomplished your task and got your mounts installed.

R,
Bullseye
Image

User avatar
blue68f100
Master contributor
Master contributor
Posts: 1997
Joined: Mon May 25, 2009 10:31 pm
Location: Piney Woods of East Texas

Post by blue68f100 » Fri May 08, 2015 12:52 pm

Glad you had success. Working with SS can be a challenge. It also helps to use a good cutting oil and new high quality taps. I like using a drill press/end mill to drill and hold the tap position while tapping. Before moving over to the next position. Working with small fine thread taps, they break so easy.....:(

I had some exotic SS for work that was so tough that the machinist would make a 1" pass then back and replace the solid carbide 3/16" endmill. I ended up ordering a case of double ended end mills for that job. That stuff was hard and work hardened even more once the cutter got dull. They sure were glad when that job finished. :D
David

SS MKIII 6 7/8" Fluted Hunter. Mueller Quick Shot, Bushnell 2x Scope, Hogue Rubber Grips
Custom Built 1911

stork
Advanced contributor
Advanced contributor
Posts: 333
Joined: Tue Aug 16, 2005 10:12 am
Location: North Dakota

Post by stork » Fri May 08, 2015 3:37 pm

I have a good drill press, but no mill. So I guess I could have used the press to keep things aligned. My issue is that you don't have the same "feel" when doing things with a press. And, all my tapping experiences have been by hand, I know what that feels like. I just wouldn't trust myself any other way.
"A free people ought not only to be armed and disciplined, but they should have sufficient arms and ammunition to maintain a status of independence from any who might attempt to abuse them, which would include their own government.” – George Washington

User avatar
blue68f100
Master contributor
Master contributor
Posts: 1997
Joined: Mon May 25, 2009 10:31 pm
Location: Piney Woods of East Texas

Post by blue68f100 » Fri May 08, 2015 6:48 pm

You actually put a pilot in the drill to hold the tap/handle vertical on a center. Most have a center cut in them. You still turn the tap by hand, so you have the feel. You just keep enough pressure on the center to keep it straight. This eliminates the chance of breaking the tap due to alignment.
David

SS MKIII 6 7/8" Fluted Hunter. Mueller Quick Shot, Bushnell 2x Scope, Hogue Rubber Grips
Custom Built 1911

User avatar
Bullseye
Site Admin/Host
Site Admin/Host
Posts: 6382
Joined: Sun Aug 14, 2005 12:23 pm
Location: USA

Post by Bullseye » Fri May 08, 2015 8:59 pm

I use the quill on the mill to achieve the same level of stability for the tap.

R,
Bullseye
Image

User avatar
charlesb
Master contributor
Master contributor
Posts: 689
Joined: Wed Feb 10, 2010 10:39 pm
Location: Mountains of West Texas

Post by charlesb » Fri May 08, 2015 10:20 pm

I use the drill-press and its vice when I can. Sometimes though, I have to tap by hand. Either way, using a tap always makes me a bit nervous, so I take it extra slow.

Once I had to tap a hole for a Winchester shotgun and it required a 1/4-24 tap. The odd-ball tap was hard to find, but finally I found one at a Harley Davidson dealer, of all places. Apparently there's something on older Harleys that uses 1/4-24.

Post Reply