Win 296 light load

The place to discuss reloading techniques.

Moderators: Bullseye, Moderators

User avatar
Hakaman
Master contributor
Master contributor
Posts: 1923
Joined: Thu Jan 15, 2009 8:51 pm
Location: detroit, michigan

Win 296 light load

Postby Hakaman » Thu Aug 10, 2017 5:19 pm

I have been loading my 44 mag with Win 296 @23g (book says 22-24g).This is a hefty load with plenty of kick. I loaded 10 rounds ea @ 21g, 20g, 19g, 18g, and 17g, and enjoy the 17g load. This of course is below the book range, and I have heard some warnings about loading this way with 296. What is your experience ?

User avatar
ruger22
Master contributor
Master contributor
Posts: 1559
Joined: Mon Apr 13, 2009 10:35 pm
Location: Virginia

Re: Win 296 light load

Postby ruger22 » Mon Aug 14, 2017 12:48 pm

I have zero experience with reloading. Sorry I can't help. but I thought I'd post something so your new thread wouldn't be so lonely. I hope you get some good replies, but GTO is pretty dead these days.
*2 Bearcat stainless, w/ EWK ejector housings & Wolff springs
*SP-101 .22LR, w/ Wolff springs
*SP-101 .357 snub w/ Wolff springs
*10/22 Deluxe Sporter, unmodded!

User avatar
bearandoldman
Ye Loquacious Olde Pharte
Ye Loquacious Olde Pharte
Posts: 4191
Joined: Tue Aug 16, 2005 10:30 am
Location: Mid Michigan

Re: Win 296 light load

Postby bearandoldman » Mon Aug 14, 2017 7:46 pm

for light loads for 25 yards have had good licj with Trail Boss, it fills the casw well and is used for cowboy loads. try around 33 to 4 grain, have used 205 in .38 and it wors great at 25, will not hit the paper at5
this was with HBWC soft lead bullets
You have great day and shoot straight and may the Good Lord smile on you.
Image

User avatar
blue68f100
Master contributor
Master contributor
Posts: 1989
Joined: Mon May 25, 2009 10:31 pm
Location: Piney Woods of East Texas

Re: Win 296 light load

Postby blue68f100 » Fri Aug 18, 2017 8:51 am

W296/H110 does not download well at all and gets very spikey when done. This powder was designed for full power loads for the Magnums and 30 carbine. Use a different powder if you want reduced loads. TB is good as well as a few others. Most powders will be very dirty when down loaded.
David

SS MKIII 6 7/8" Fluted Hunter. Mueller Quick Shot, Bushnell 2x Scope, Hogue Rubber Grips
Custom Built 1911

noylj
New member
New member
Posts: 1
Joined: Thu Jul 02, 2015 12:20 am

Re: Win 296 light load

Postby noylj » Mon Aug 21, 2017 3:31 pm

296/H110 is a relatively difficult powder to ignite that requires pressure and temperature to burn.
It was found that going much below the MAX load, one could end up with a partial molten mass of powder stuck in the barrel and the NEXT shot would see a KB from the obstruction.
This is not an every time occurrence, nor is it one where you can go on past problem-free shooting to know you are OK.
Most loading manuals, I would hope, have warnings, but they are often rather poorly written.
From Hodgdon:
H110 Loads should not be reduced more than 3%. Reduce H110 Loads 3% and work up from there. H110 if reduced too much will cause inconsistent ignition. In some cases it will lodge a bullet in the barrel, causing a hazardous situation (Barrel Obstruction).
This may cause severe personal injury or death to users or
bystanders.
DO NOT REDUCE H110 LOADS BY MORE THAN 3%.

User avatar
Hakaman
Master contributor
Master contributor
Posts: 1923
Joined: Thu Jan 15, 2009 8:51 pm
Location: detroit, michigan

Re: Win 296 light load

Postby Hakaman » Sun Aug 27, 2017 9:54 pm

I instead have loaded some lighter rounds with Winchester 231 as per Lyman reloading manual. They are all within the suggested range the book offers, but are at a slower FPS then the full loaded Winchester 296 rounds. I am not going to lower the Winchester 296, nor any other powder outside of what the book suggest.


Return to “The Reloading Bench”

Who is online

Users browsing this forum: No registered users and 3 guests