Search found 11 matches
- Mon Jul 02, 2018 10:07 pm
- Forum: Rimfire Handguns
- Topic: The new Ruger Mark IV Target and Hunter
- Replies: 13
- Views: 133369
Re: The new Ruger Mark IV Target and Hunter
I decided to get the Mark iv Hunter, loved the 6.88 inch fluted barrel. If you have a Field and Stream store nearby ( yes, I know they Played to the anti-gun media and took all ARs out) be aware that they do price matching. I showed an add from Bud's Guns on my phone and saved over $100 off their pr...
- Sat Apr 07, 2012 10:24 pm
- Forum: Rimfire Handguns
- Topic: MarkII sight questions
- Replies: 9
- Views: 9397
sight adjustment
I drifted the rear over, now the windage is dead on. I am putting an orange sticker 4" higher than my target and can get 7 to 8 out of ten hits. I am holding off on taking material off of the front blade for now. I may order an extra blade next time I need a part and experiment. I use whatever bulk ...
- Tue Apr 03, 2012 9:47 am
- Forum: Rimfire Handguns
- Topic: MarkII sight questions
- Replies: 9
- Views: 9397
mark II sights
Thanks for the information guys!
- Mon Apr 02, 2012 9:24 pm
- Forum: Rimfire Handguns
- Topic: MarkII sight questions
- Replies: 9
- Views: 9397
MarkII sight questions
I recently picked up a used Mark II with 4.5" tapered barrel with fixed sights. I love it except for the sights. At 50' from a rest, my point of impact is about 5" left and 3" low of center. My questions are: Can the fixed rear sight be drifted over? Can I raise the point of impact by filing down th...
- Thu Dec 29, 2011 1:44 pm
- Forum: Rimfire Handguns
- Topic: My Ruger MKII Competition Target Model
- Replies: 18
- Views: 17800
- Fri May 06, 2011 3:08 pm
- Forum: Technical Forum
- Topic: 22/45 bolt problem
- Replies: 6
- Views: 6931
- Tue May 03, 2011 9:57 am
- Forum: Technical Forum
- Topic: 22/45 bolt problem
- Replies: 6
- Views: 6931
- Mon May 02, 2011 2:23 pm
- Forum: Technical Forum
- Topic: 22/45 bolt problem
- Replies: 6
- Views: 6931
22/45 bolt problem
I have recently installed a new hammer bushing and removed the magazine safety and LCI. Functions test and dry firing were good and the trigger pull felt better. I ran into trouble at the range. The first shot of the magazine was fine, then the bolt would not fully close (out of battery) with all 9 ...
- Tue Apr 26, 2011 2:10 pm
- Forum: Rimfire Handguns
- Topic: Mark III Bolt Action Roughness
- Replies: 15
- Views: 12567
- Fri Apr 08, 2011 10:54 am
- Forum: Technical Forum
- Topic: Ruger MKIII firing pin stop
- Replies: 15
- Views: 24659
MK III firing pin stop
Thank's Bullseye, I'll keep that in mind.
- Thu Apr 07, 2011 2:01 pm
- Forum: Technical Forum
- Topic: Ruger MKIII firing pin stop
- Replies: 15
- Views: 24659
Ruger Firing pin stop
After detail stripping of my MKIII 22/45, i could not re-insert the firing pin stop (roll pin style). I had a shoot the next day so I improvised and cut the shaft from a dremmel accessory. After smoothing out the cut with a file it fit perfectfully and has held up well so far-about 600 rds. My quest...