Bullseye asked that I paste my Pictures over in the Technical Area as in the future a P85/P89/P90/P93/P94 owner can find the info..
Note: That several of the parts of the various models are different & the Deckocker only are also slightly different..As well as different recoil rod assemblies & barrel links etc..
This picture thread was made with a 1993 P89 Frame that recieved a Mid 2000s parts kit, The slide break down was done on the original 1993 slide
Ruger P-89 Disassembly Picture Manual
WARNING If You Don't Have the Propper Skills To Try Any Of This Then You Should Seek Out A Qualified Gunsmith
Do This Of Your Own Risk..
Safety Glasses Should Also Be used as a Few of The Parts are Under Spring Tension & Could Fly Away & Cause Injury To Your Eyes
I am taking the time to make this manual because I couldn't find any information On The P- Series Rugers when I started my "Project P-89"
Maybe in the Future this can help someone else out..
Enjoy!!
Gary
***Safety First** Check Breach For Live Ammo
Check Magazine For Ammo, On the Ruger You Will Need The Magazine To Push The Ejector Back Up After Reassembly
Push Down Ejector
Pull Slide Back Slightly & Pull Out Slide Relese Rever
Remove Slide
Remove LH Grip Screw
Remove RH Grip Screw, Push Slide Release Lever Back In So Frame Will Lay Flat
Remove Grips by Reaching Inside The Magazine Well & Pushing Them Out
Magazine Catch
Remove Magazine Catch
Remove Magazine Catch
RH Magazine Catch Removed
Remove LH Magazine Catch
Remove Magazine Catch Spring by Lifting Up Back & Out Threw Magazine Well
Mainspring Plunger Cap, With Hammer in The Not Cock Position Press the Cap onto your workbench hard while pressing out the pin then release SLOWLY
Removed Mainspring Plunger, Mainspring, & Hammer Strut
Ejector Assembly
Pushing Out Ejector Pin, Capture the Spring when you remove the Punch it's under some preasure
Ejector Assembly, Ejector Spring & Ejector Pin Removed
Sear Blocking Lever
Sear Pin
Pushing Out Sear Pin From Frame
Sear, Sear Spring & Pin Removed
Blocking Lever
Pushing Out Blocking Lever Pin From Frame
Blocking Lever Pin Removed
Hammer Pivot Pin
Removing Hammer Pivot Pin & Lift Hammer Forward Down Then Up to Remove
Hammer & Pivot Pin Removed
Trigger & Trigger Bar
Lifting Slide Stop Lever Retaining Spring
Removing Slide Stop Lever
Removing Trigger & Trigger Bar
Driving Out Spring Retainer into frame, Use 1/16" Punch
Spring Retainer Removed
Trigger Return Spring Plunger Plug
Removing Springs & Plug
Springs Retainer & Trigger Return Spring Plunger Removed
Tools Used To Strip Frame
Parts Removed In Container As Not To Lose Anything
Slide Assembly
Removing Recoil Rod & Spring
Remove Barrel
Levering Out Extractor Toward Ejection Port While Levering Toward The Muzzle
Remove Extractor
Remove RH Side safety Lever, NOTE: Detent & Spring At The Bottom Cover With Finger While Removing Or It Might Fly Away
RH Safety Removed, NOTE: Detent & Spring Under It
Turn LH Safety Down 90 Degrees
Capture Firing Pin & Return Spring While Removing Safety Lever
Removing Safety & Firing Pin
Slide Parts Removed
Loosten Rear Sight Allen Set Screw, Turn Counter Clockwise 5/64" Allen Wrench or Hex Bit
Allen Screw Removed
Driving Out rear Sight To The Right, NOTE: Brass End On My Push Tool as Not To Mark Up Sight
As You Remove The Sight NOTE: Firing Pin Safety Spring & Plunger, These Can Easily Be Lost
Slide Stripped Except For Front Sight Assembly, The Front Sight Removal Requires That You Drive Out Both 1/16" Roll Pins With A Roll Pin Punch & Then Either Use A Vise Or Vise Grips To Pull The Sight Out Or Tap Slightly With a Brass Punch
When Reinstalling RH Safety You Must Depress The Dentent & Spring as You Push It Into Place
When Installing The Extractor I Found Using a Wooden Dowel Threw the Barrel Hole In The Front Of The Slide The Easiest, Tap Lightly on the Dowel with a Small Hammer Till It Pops Back Into Place
Checking Firing Pin Protudtion By Pushing on The Firing Pin From The Rear While Pushing The Firing Pin Safety Plunger, You Can Also Check The Firing Pin Safety This Way By Pushing The Firing Pin In as Far as It will go then depress the firing pin safety plunger & it should then allow the firing pin to move forward into the breach face..
Enjoy!! Stay SAFE & Shoot OFTEN!!
Gary aka BerettaPistols/Headknocker
I now have a PDF available of this & it can be sent via email..
[email protected]
Ruger P89 Disassembly Picture Manual
Moderators: Bullseye, Moderators
- HEADKNOCKER
- Regular contributor
- Posts: 99
- Joined: Sun Jan 03, 2010 8:51 pm
- Location: Louisville KY
- HEADKNOCKER
- Regular contributor
- Posts: 99
- Joined: Sun Jan 03, 2010 8:51 pm
- Location: Louisville KY
Steve @ Steve's Pages has hosted my homemade manual in PDF at his website & here's the link to it..
http://stevespages.com/pdf/ruger_p89_di ... manual.pdf
If you can't go directly to that PDF Go to Steve's Manuals page here..
http://www.stevespages.com/page7b.htm
Select - The Manual Ruger Forgot To Write - P89 Disassembly Picture Manual
http://stevespages.com/pdf/ruger_p89_di ... manual.pdf
If you can't go directly to that PDF Go to Steve's Manuals page here..
http://www.stevespages.com/page7b.htm
Select - The Manual Ruger Forgot To Write - P89 Disassembly Picture Manual